Socket Dimension Chart

September 19, 2024 Post a Comment

Socket dimension chart

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).

How do you read a socket size?

It's important to note that socket sizes are actually given in two measurements, namely: The size of the drive socket (the part that attaches to the socket wrench). These are always given in imperial measurements, and will usually be either 1/4", 3/8", 1/2", 3/4" or 1".

Are 3/4 and 19mm the same?

19mm = 3/4 inch. 20mm = 25/32 inch. 21mm = just over 13/16 inch. 22mm = almost 7/8 inch.

What are the 3 socket sizes?

Socket Drive Sizes Metric and Standard (SAE) sockets come in three available drive sizes: 1/4 inch, 3/8 inch, and 1/2 inch. The measurement refers to the size of the square used to attach the to socket to a wrench or a ratchet.

What are the 3 types of sockets?

Three types of sockets are supported:

Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
Datagram sockets allow processes to use UDP to communicate. ...
Raw sockets provide access to ICMP.

What are the standard socket sizes in order?

Six Point Standard Sockets (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)

How are 12 sockets measured?

Socket Sizes:SAE (INCH, fraction) & Metric (mm) In the current market, socket sizes are divided into two systems: SAE (imperial, measured in inches) and metric (measured in millimeters). Both 6-point and 12-point sockets are measured using these two systems.

What size is a 15mm socket?

3/8″ Drive	1/4″ Drive	1/2″ Drive
11mm	8mm	14mm
12mm	9mm	15mm
13mm	10mm	16mm
14mm	11mm	17mm

What are the 3 common sizes of ratchets?

Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.

Can I use a 3/4 socket instead of a 19mm?

No, there's no need to get a 19mm socket, and it will present no difference in performance just because the number on the side is different.

What is a 3/4 wrench in metric?

3/4" 29mm. 1-1/8" 32mm. 1-1/4"

Is 21mm the same as 13 16?

Indeed. A 13/16 is just under 21mm.

What is metric and SAE?

SAE sockets are sized in inches and fractions of inches. Metric and SAE wrenches have different systems of measurement. Metric sockets and wrenches use the metric measurement system. This is when millimeters are used to describe the size. So you'd get a 20mm wrench in the metric unit of measurement.

What does SAE stand for in measurement?

Standard American English and the Metric System Today, measuring in feet and inches is part of the Standard American English (SAE) or Imperial units of measurement, along with volumes like gallons and fluid ounces and weights like pounds.

What are the different types of sockets?

Quick Check

Common Types of Socket and Their Uses.
Hex Sockets.
Spark Plug Sockets.
Impact Sockets.
Universal Joints Sockets.
Insulated Sockets.
Socket Bits.
Pass-Through Sockets.

Whats bigger 3/8 or 1/4 socket?

3/8 is expressed as 0.375 as a decimal and 1/4 is expressed as 0.25 in its decimal form. It is clear that the value of 3/8 is more than 1/4. Hence, it is bigger.

What are 12 point sockets used for?

The additional points make these sockets easier to connect with the heads of fasteners. This is ideal if you are trying to work on a fastener that is hard to see or you cannot see at all. 12 point sockets are also great for use in tight spaces as they allow you to connect to a fastener at more angles.

What is the best type of socket?

Six-point sockets are sturdier than 12-point sockets because they have thicker walls. These sockets are best for high-torque applications, but they are also the most commonly used of the two types. Six-point sockets apply force to the flat sides of the fastener, making them less likely to slip off of rounded edges.

What does SAE stand for on tools?

SAE, which stands for the Society of Automotive Engineers, was used as the standard primarily on U.S.-made cars and trucks through the 1970s. SAE sockets are sized in inches and fractions of inches.

How do you measure bolt socket size?

How to Determine the Right Size Socket for a Nut

Turn on the digital caliper and set it to read in inches, not millimeters.
Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides.
Check the caliper display. ...
Turn on the digital caliper and set it to read in millimeters, not inches.